MikMek Micro Plus Operator's Manual

LEMUR TICKET PRINTERS Operator’s ManualLemur Lemur-SLemur-2 Lemur-KLemur-2KRevA: 12.04.09

7.0 Standard Interface Pinouts RJ12 Serial Connection RJ12 Connector +5VDCTYPICAL DB9 to RJ12 PIN CONNECTIONS 9 pin host BOCA RJ12 2 2 Transmit3 3 Re

108.0 Thermal Paper - Theory & SpecificationRefer to the BOCA Systems website at www.bocasystems.com, THERMAL TICKETS section for the most current

9.0 Maintenance and AdjustmentsYour ticket printer is solidly constructed and has been designed for high volume use. It requires minimal care to pr

9.1.1 Cut or Tear OptoThere is one optical sensor (opto) mounted on an adjustable aluminum bracket. The opto controls the cut or tear position. Remov

9.1.2 THERMAL PRINT HEADThe print head should be cleaned periodically to prevent debris from building up on the print element. The required cleaning

9.1.3 Platen (Rubber Driver Roller)The Platen (rubber drive roller) should be cleaned once a year to prevent paper dust from building up on the roller

9.1.4 Ticket Width Adjustment To adjust the paper path for use with a different ticket width, adjust the slider bar to the fully open position.Insert

9.2 Cutter Assembly The BOCA cutter system is a fully integrated cutter knife mechanism powered by a stepper motor.The cutter requires no adjustments

9.3 Logic Board The printed circuit boards used in this product have been manufactured using surface mount technology. These printed circuit boards c

189.3.2 Logic Board (Installation) 1. Installed the logic board into the printer. 2. Install the four 3/16” head screws that hold the logic board onto

1Table of Contents Page FCC Notice & Warranty Information 2 1.0 Introduction 3 2.0 Unpacking the p

19Above and below photos are of a Lemur with optional LCD display and cutter 27141742212131222411263515821720

Lemur-S with optional cutter 35313531356View with cover removed.15262172081618View with thermal head unlocked and open.101923120

Lemur-S with optional cutter Lemur-2K with optional cutters12929128282020332323341172212313View with rear access panel removed.1432421

Lemur-2 without optional LCD display 3033121132511411.0 Troubleshooting GuideThis is a simplified troubleshooting guide listing some of the typical pr

23 c. Check that the ticket stock is being loaded correctly. Consult “Installation” section. d. Contact your system provider or BOCA for further as

APPENDIX A - CONTROL PANEL The FGL46 printers allow the user to adjust various printer options through the optional control panel. To access the cont

The following is a brief overview of some representative Menu options: BAUD RATE? Controls the serial interface baud rate, parity bit, data bits and

INC CUT1/2 COUNT? moves the cut/tear position to the left (towards the ticket entrance area). Cut counts are increments of .003” for 300dpi and .005”

APPENDIX B - VERTICAL PRINTER INSTALLATIONPrepare the counter top by cutting a rectangular hole in accordance with the dimensions specified for your p

APPENDIX C – LEMUR-2 OR LEMUR-2K Ticket Load Procedure for a Lemur-2 Printer Your printer may vary from the above photoFeed DirectionPath 2 Path 1 Tur

2FCC NOTICE NOTE: The equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rule

29APPENDIX D – CHANGING ETHERNET PARAMETERS CHANGING 'IP ADDRESS'1. Please follow these steps to change the fixed IP address on your Ethern

APPENDIX E – INTERFACE TESTING A LEMUR Boca Systems, Inc. has developed a program that allows customers to communicate from a host computer to the pri

6. Now click on the “Select Printer Operation” drop-down arrow and chose the appropriate test program.If your printer has FGL firmware then chooses “F

Above sample FGL ticket was printed on a 2” x 5.50” (concert) ticket using a RADJW-2” 300dpi FGL printer. Above sample FGL ticket was printed on a 3.2

33Click here to return to > Table of ContentsAbove sample PCL ticket was printed on a 3.25” x 5” ticket using a RADJW-3.25” 300dpi PCL printer.

APPENDIX F – DOWNLOADING SOFTWARE COMMANDS For those Lemurs model printers without LCD display the menu setting changes may be done by utilizing the s

35The following list shows all of the commands necessary to access the operator control panel functions. BAUD RATE COMMAND - <brx,y,z> (printer

364 - reverse adjustable 2” path1 5 - reverse adjustable 2” path2 6 - reverse adjustable 2” both paths 7 - reverse adjustable 2.5” path1 8 - reverse a

37ETHERNET MODE COMMAND - <eth#> (printer will reset after receipt of command)This command sets the Ethernet mode for the printer and is permane

38PERMANENT DEFAULT GATEWAY IP ADDRESS COMMAND - <dgw10.0.1.254> (printer will reset after receipt of command). Note: This function should only

1.0 IntroductionThe Lemur series printers are direct thermal ticket printers that may be purchased with optional integrated cutting mechanism and LCD

39APPENDIX G – CONFIGURE WI-FI CONNECTION To use the wireless capabilities of a printer equipped with the optional wireless interface (Wi-Fi), it will

3.0 Important Safety Information WARNING: The appearance of this symbol indicates the proximity of an exposed high voltage area. Please follow all

54.0 Installation The Lemur series printer was designed to be mounted either on a desktop or shelf (horizontal model) or vertically in a counter top (

Above sample was printed on a 4”x6” ticket using a 300dpi Lemur without cutter. Above sample was printed on a 2” x 5.5” ticket using a 200dpi Lemur wi

5.0 Ticket Load Procedure Turn the printer on and wait five seconds. The red CHECK PAPER led will be illuminated (if your printer has an optional LC

Two typical ticket formats and feed directions are shown below. Black Mark Underside of TicketCinema5.50”Black Mark Underside of TicketStandard Ticke